Best Quality Acrylic Paint Cheap With Solvent Thinner Road Marking
Paint Reflective Road Marking Paint Acrylic Thinner
This product is composed of acrylic resin, plasticizer,
sun-resistant pigment and organic solvents. Meanwhile, the paint
film is clear, bright, highly visible and has excellent weather
This paint is designed for the sign and protection of cement
chimneys and steel structure tower.
rReady to use.
rReady to use.
Acrylic paint thinner
● Airless Spray:
Nozzle tip: 0.017~0.023 inch.
Spray pressure: 15~18 MPa.
Thinner ratio: 0~15% (by weight of paint).
● Brush, Roller:
Must achieve required thickness.
|Substrate temperature||10 °C||20 °C||30 °C|
|To touch (50um)||2h||1h||30min|
|To handle (50um)||8h||4h||3h|
|Min. recoating time||8h||4h||3h|
|Max. recoating time||-||-||-|
|* Make sure no chalking and other contaminations before recoating.|
|* Above data for reference only, actual drying time and recoating
time is dependent on temperature, dry film thickness, ventilation
condition, humidity, mechanical strength,etc.|
A: For the concrete base floor, first ensure reliable
moisture-proof facilities are set below the base concrete. New
concrete or the cement base shall be cured for at least 28 days
with moisture content not exceeding 5%. The moisture content shall
be evaluated empirically.
B: The surface of the base shall be clean, firm and free from
contaminants such as mortar paint splashes, curing agent, grease,
etc. It’s better to roughly polish the excessive floating pulp and
grind the oily ground with electric angle grinder.
C: Defects such as cracks and drums shall be repaired first.
D: The surface shall be clean, firm and dry whatever methods are
used to treat it. Above all, the surface shall not be in the state
of rising moisture.
E: The base layer shall be cleaned and burnished with a grinder.
Substrate temperature shall be at 3 ℃ higher than dew point,
relative humidity less than 85%. Measurement of temperature and
humidity should be close to substrate.
Safety and Healthy
All surfaces to be coated shall be clean and dry. The surface shall
be evaluated and treated according to ISO8504 standard.
Steel: Sanding to Sa2.5 (ISO8501-1:2007). It is acceptable to
polish by power tools to meet at least St2.0 (ISO8501-1:2007).
Concrete substrate coating surface treatment:
a. Concrete grass-roots floor, first of all, must confirm whether
the base surface concrete below whether there is a reliable
moisture-proof facilities. New concrete or cement base at least 28
days of maintenance time, and its water content should not exceed
5%, using empirical methods to assess the water content of the
b. The grass-roots floor surface should be clean, solid and free of
contaminants, such as mortar and paint sputtering, maintenance
agents, grease, etc. For too much floating pulp, it is best to use
light roughing, grinding. Oily ground, using electric angle grinder
c. The surface of the ground cracks, empty drums and other defects
should be repaired and flat.
d. No matter what method is used to treat the surface, it must
eventually be clean, solid and dry on the grass-roots surface. It
is particularly important that the grass-roots level must not be in
a state of rising moisture.
e. Grassroots clean-up, polished with a polishing machine.
Store this product in shady, dry, and ventilated warehouse. The
shelf life is 12 months at room temperature. If exceeding shelf
life, the products shall be tested before using.
All technical data given in this document is based on our knowledge
achieved in lab and practice, it is not completely correct.
Although we try to keep the validity of our advice, however we
cannot predict the practical conditions that will affect paint
quality. Herein, we cannot be responsible for the consequences of
variations in such conditions, or for unforeseen conditions. We
reserve the right to modify this document without informing in