Wholesale Epoxy Zinc Workshop Primer with excellent performance in
cathodic protection, adhesion
This two-component product is mainly composed of epoxy resin by
adding superfine zinc powder, anti-rust pigment, polyamide adduct
curing agent, etc. Significantly, its film is provided with
excellent performance in cathodic protection, adhesion as well as
rust-resistance. Meanwhile, this coating would not be burnt
seriously during wielding and cutting. Furthermore, it is resistant
to oil, water and solvent.
This product is widely used for a wide range of floors with various
levels of mechanical and chemical exposure, such as warehouse,
garage, office building and laboratory. What’s more, it also can be
used for hospital, electronics factory,food and beverage factory.
Use the power mixer to mix the main paint evenly, and then as you
stir it, you add the hardener until you get to mix well.Generally,
if the temperature below 10 ℃,it needs 20 min induction time; if
the temperature over 10℃, it needs 15 min induction time.
● Mixing Ratio:
Part A: Part B= 20: 5 (by weight).
Epoxy paint thinner.
● Airless Spray:
Nozzle tip: 0.015~0.021 inch.
Spray pressure: 15~18 MPa.
Thinner ratio: 0~10% (by weight of paint).
● Brush, Roller::
Recommended for small areas only. Must achieve required thickness.
|Substrate temperature||10 °C||20 °C||30 °C|
|To touch (1mm)||2h||1h||30min|
|To handle (1mm)||48h||24h||12h|
|Min. recoating time||6h||4h||2h|
|Max. recoating time||10h||7h||5h|
|* Make sure no chalking and other contaminations before recoating.|
|* Above data for reference only, actual drying time and recoating
time is dependent on temperature, dry film thickness, ventilation
All surface to be coated shall be clean and dry. The surface shall
be evaluated and treated according to ISO8504 standard.
Steel: Sanding to Sa2.5 (ISO8501-1:2007). It is acceptable to
polish by power tools to meet at least St2.0(ISO8501-1:2007).
Concrete surface treatment:
a. First of all, it is necessary to confirm whether reliable
damp-proof facilities are installed below the concrete base. The
new concrete or cement base should be cured for at least 28 days,
and its moisture content should not exceed 5%. The moisture content
of the base should be evaluated by empirical method.
b. The base surface should be clean, solid and pollution-free, such
as slurry and paint splashing, curing agent, grease and so on. For
excessive float pulp, it is better to first use slight roughing,
polishing, oil-stained ground, using electric angle grinder to
c. The cracks and empty drum on the floor surface should be
d. Whatever method is used to treat the surface, a clean, solid and
dry base surface must be obtained. It is especially important that
the grassroots should not be in a state of rising tide.
e. The base layer is cleaned and sanded with a sander.
Safety and Health
Please refer to MSDS before using this product. If you do not fully
understand the restrictions, or cannot follow MSDS directions
strictly, do not use this product. This volatile product is
flammable. Keep this product away from flame or fire. Smoking is
strictly prohibited in working area. Keep working area ventilated
during application to make sure solvent vapor content is low in the
air. PPE is necessary to avoid this product contacting with eyes or
skin. More detailed safety tips are based on practical situation.
Please handle used paint barrel correctly to avoid any pollution.
Store this product in shady, dry, and ventilated warehouse. The
shelf life is 12 months at room temperature. If exceeding shelf
life, the products shall be tested before using.
All technical data given in this document is based on our knowledge
achieved in lab and practice, it is not completely correct.
Although we try to keep the validity of our advice, however we
cannot predict the practical conditions that will affect paint
quality. Herein, we cannot be responsible for the consequences of
variations in such conditions, or for unforeseen conditions. We
reserve the right to modify this document without informing in
|Packaging||Packing size||Packing weight|
|Part A||20L||20 KG|
|Part B||6L||5 KG|